Go Back   R/C Helicopter Fever Forum > RC Helicopter Fever > Getting Started in R/C Helicopters
Reload this Page dragonfly 36
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Getting Started in R/C Helicopters For beginners who are just starting off. Questions? Answers? Get them here.


Our Sponsors

Reply
Page 1 of 2 1 2 >
 
Thread Tools
  #1  
Old 09-04-2007, 02:45 AM
Aussie62 Aussie62 is offline
Newbie Member
  
Join Date: Sep 2007
State: Queensland
City: Mackay
Country: Australia
Posts: 4
dragonfly 36
Am only new flyer, & have just purchased a dragonfly 36 but the brushless motor wont run & tail servo motor makes a noise like it has stripped gears in it? can anyone give me some pointers please.:
Reply With Quote
  #2  
Old 09-04-2007, 02:59 AM
Aussie62 Aussie62 is offline
Newbie Member
  
Join Date: Sep 2007
State: Queensland
City: Mackay
Country: Australia
Posts: 4
Re: dragonfly 36
Also if anyone has the correct settings for a mode 1 transmitter & the connections for the 36 heil would be grate the place that sent it sent a dud
Reply With Quote
  #3  
Old 09-04-2007, 05:53 AM
BABY HUEY's Avatar
BABY HUEY BABY HUEY is online now
Flying Member
  
Join Date: Jun 2007
State: MISSOURI
City: CUBA
Country: USA
Posts: 702
Re: dragonfly 36
Hello Aussie62,

Your throttle channel is probably reversed keeping the esc from arming. Also the tail servo needs to be centered and the travel should be adjusted to stop overtravel. I am sorry for that I do not have the time to go into this further now but if you check out the Walkera section of this forum you will discover most of your answers there.

Good flying,
Huey
__________________
We have nothing to fear but fear it's self! And the hard, hard reality of subterranean flight!

Walkera 36- 430L,30amp esc, Futaba 6ch
Walkera 36- basket case-Comet 500, Kalt Baron Whisper, Caliber 30
GMP/ HIROBO COBRA 50 FLYING!!
Reply With Quote
  #4  
Old 09-04-2007, 06:48 AM
Aussie62 Aussie62 is offline
Newbie Member
  
Join Date: Sep 2007
State: Queensland
City: Mackay
Country: Australia
Posts: 4
Re: dragonfly 36
Thanks Baby Huey
I have switched the reverse sw on the transmitter but it did nothing, I'll look up what you have said Thanks 4 your help
Reply With Quote
  #5  
Old 09-11-2007, 05:19 AM
Aussie62 Aussie62 is offline
Newbie Member
  
Join Date: Sep 2007
State: Queensland
City: Mackay
Country: Australia
Posts: 4
Re: dragonfly 36
Sent heli back, am waiting for replacement will be asking heap of questions when it arrives for sure
Reply With Quote
  #6  
Old 09-25-2007, 11:00 AM
yeo5705 yeo5705 is offline
Newbie Member
  
Join Date: Sep 2007
State: wilayah persekutuan
City: kuala lumpur
Country: malaysia
Posts: 2
Re: dragonfly 36
am facing same problem ... keep spinning on ground ... some said might be problem with dip switch as acro/heli set to on ... how's urs ?
Reply With Quote
  #7  
Old 09-25-2007, 11:56 AM
BABY HUEY's Avatar
BABY HUEY BABY HUEY is online now
Flying Member
  
Join Date: Jun 2007
State: MISSOURI
City: CUBA
Country: USA
Posts: 702
Re: dragonfly 36
Hello,
Is this the six or seven channel Heli?

Huey
__________________
We have nothing to fear but fear it's self! And the hard, hard reality of subterranean flight!

Walkera 36- 430L,30amp esc, Futaba 6ch
Walkera 36- basket case-Comet 500, Kalt Baron Whisper, Caliber 30
GMP/ HIROBO COBRA 50 FLYING!!
Reply With Quote
  #8  
Old 09-27-2007, 05:10 AM
yeo5705 yeo5705 is offline
Newbie Member
  
Join Date: Sep 2007
State: wilayah persekutuan
City: kuala lumpur
Country: malaysia
Posts: 2
Re: dragonfly 36
mine is 6ch ... btw the battery indicator shows which status? heli or transmitter itself ...

thx in advanced.
Reply With Quote
Reply
Page 1 of 2 1 2 >

« Another RC Helcopter Victim.... | Radio Equipment/Heli Set up - Advice required »

Our Sponsors

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump

All times are GMT -7. The time now is 12:59 AM.
Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2009, Jelsoft Enterprises Ltd.
SEO by vBSEO 2.4.0 © 2005, Crawlability, Inc.
Helifever.com Copyright ©1997-2006

Contact Us - R/C Helicopters - Archive - Top